Brocade Communications Systems S3-1002483-03 Uživatelský manuál Strana 102
- Strana / 206
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
90 Brocade BigIron RX Series Hardware Installation Guide
53-1002483-03
Managing the interface modules
4
Synchronizing the interface modules’ IronWare images during bootup
By default, the BigIron RX Series system checks the IronWare images in the interface module’s
flash memory during boot to ensure they are the same as the IronWare images in the management
module’s flash memory. If an interface module does not have an IronWare image, the system
automatically downloads the image from the management module’s flash memory to the interface
module’s flash memory.
If an interface module has different IronWare images, the system prompts you to do the following:
• If you want to update the primary and secondary IronWare images in the interface module’s
flash memory with the images in the management module’s flash memory, enter the lp
cont-boot sync <slot-number> command at the Privileged EXEC prompt.
• If you want to retain the IronWare images in the interface module’s flash memory, enter the lp
cont-boot no-sync <slot-number> command at the Privileged EXEC prompt.
Specifying an immediate synchronization
You can immediately synchronize the IronWare images between the management module and one
or all interface modules. For example, to immediately synchronize the IronWare images between
the management module and all interface modules, enter the following command at the Privileged
EXEC level:
BigIron RX# lp sync all
Syntax: lp sync all | <slot-number>
The all keyword indicates that the immediate synchronization applies to all interface modules in the
BigIron RX Series chassis.
The <slot-number> parameter specifies the BigIron RX Series chassis slot number that contains
the interface module to which the immediate synchronization applies. You can specify 1 – 4 for
BigIron RX-4, 1 – 8 for BigIron RX-8 or 1 – 16 for BigIron RX-16.
Disabling or reenabling an automatic check and synchronization
By default, the BigIron RX Series system checks the IronWare images in the interface module’s
flash memory during bootup to ensure it is the same as the IronWare images in the management
module’s flash memory. For information about what the system does if the interface module does
not currently have a IronWare image or if the image is different from that of the management
module, refer to “Synchronizing the interface modules’ IronWare images during bootup” on
page 90.
To disable the automatic check and synchronization during bootup, enter the following command at
the global CONFIG level:
BigIron RX(config)# lp disable-lp-sync-check
Syntax: lp disable-lp-sync-check
Provided that you save this configuration by entering the write memory command, the system will
disable the automatic check and synchronization of the IronWare images starting with the next
software reload or system reset and each reload or reset after that.
To re-enable the automatic check and synchronization of the IronWare images during bootup, enter
the following command at the global CONFIG level:
BigIron RX(config)# no lp disable-lp-sync-check
- Brocade BigIron RX Series 1
- Document History 2
- Contents 3
- About This Document 9
- Trademark references 10
- Related publications 11
- Getting technical help 11
- Document feedback 11
- Product Overview 13
- Hardware features 14
- FIGURE 2 BigIron RX-8 chassis 15
- BigIron RX-16 chassis 16
- BigIron RX-4 17
- BigIron RX-8 18
- BigIron RX-16 18
- Management modules 19
- PCMCIA slots 20
- Console port 20
- 10/100/1000 Ethernet port 20
- Interface modules 21
- • Eight LEDs 22
- LED Position State Meaning 23
- Position State Meaning 25
- (Mini RJ 21 Copper) 26
- Switch fabric module 27
- Power supplies 28
- Cooling system 29
- • Leave the fan speed as is 31
- • Increase the fan speed 31
- • Decrease the fan speed 31
- Supported software features 32
- Installation precautions 33
- Power precautions 34
- Cabling infrastructure 36
- Installation location 37
- 2Shipping screws 38
- 1 Standard 19 inch rack 39
- Removing the slot blanks 40
- Interface modules 1 – 4 41
- 1 Management module 42
- 1 Power supply 43
- 2Power cord 44
- Final steps 45
- 2Chassis rear 48
- Interface modules 1 – 8 50
- 1Power supply 52
- 1 Lift handle 3 Power cord 53
- • “Removing the slot blanks” 57
- Interface modules 1 – 16 60
- 1Interface module 61
- 1 Lift handle 4 Ground point 64
- 3Power cord 64
- Powering-on the power source 67
- Verifying proper operation 68
- • Make certain that the 69
- • The module may not be 70
- • Check the Pwr LED on the 70
- • Enter the show chassis 70
- • Make sure that the power 71
- • Make sure that the wall 71
- Displaying the module status 73
- Assigning passwords 77
- Login lockout 78
- Password history 78
- Setting passwords to expire 78
- Configuring IP addresses 80
- Cabling a fiber optic module 85
- Cleaning fiber optic modules 86
- Testing network connectivity 88
- Configuration notes 89
- Command syntax 89
- • Terminated: The link is up 90
- • Failed: The TDR test failed 90
- Temperature Readings 93
- Misc Info 93
- Static and dynamic buffers 94
- High, 60 deg 95
- Low 57, deg. High, 70 deg 95
- Low, 67 deg. High, 80 deg 95
- • LP – An interface module 98
- Monitoring the cooling system 99
- This field... Displays 100
- 53-1002483-03 101
- BigIron RX# lp sync all 102
- Specifying an immediate boot 103
- Configuring an automatic boot 105
- BigIron RX# power-off lp 1 107
- BigIron RX# power-on lp 1 107
- BigIron RX# power-off snm 1 108
- BigIron RX# power-on snm 1 108
- Removing MAC address entries 110
- In this chapter 111
- Replacing a management module 111
- Removing a management module 112
- Replacing an interface module 116
- Removing an interface module 117
- Replacing a power supply 124
- 2 Fan assembly 128
- 1 Fan assembly 129
- • A small Allen wrench 131
- 2Filter 4Fan trap 132
- Software images required 133
- IronWare image 134
- Monitor image 134
- Boot image 134
- FPGA image 135
- Startup configuration file 135
- Displaying flash information 136
- Interface Modules 140
- Command change 144
- 02.6.00 and later 145
- TABLE 24 Image name 146
- TABLE 25 Image name 147
- Command syntax Description 148
- BigIron RX# show flash 151
- BigIron RX> show version 152
- Hitless Layer 2 OS upgrade 153
- Switchover 156
- Setting up consoles 157
- Verify the new software image 157
- BigIron RX# write memory 158
- BigIron RX# reload 158
- Dynamic configuration loading 160
- BigIron RX-if-e1000-3/1) 162
- File synchronization 163
- BigIron RX# sync-standby 164
- Scheduling a system reload 166
- Reloading at a specific time 167
- Canceling a scheduled reload 167
- Diagnostic error codes 168
- Hardware Specifications 169
- BigIron RX Series 170
- Amps Watts BTUs per hour 170
- Physical dimensions 171
- Operating environment 171
- Storage environment 171
- Safety agency approvals 171
- Port specifications 172
- Pin number MDI-X ports 173
- Regulatory Statements 175
- 에서 사용하는 것을 목적으로 합니다 176
- BSMI Statement 177
- Caution and Danger Notices 179
- Caution statements 180
- Danger notices 185
- Table 0.19: 186
- Table 0.20: 186
- Table 0.21: 186
- Software Specifications 193
- IP Multicast 195
- Management 195
- Internet drafts 196
- Cable cinch overview 197
- FIGURE 53 Two mRJ21 cables 198
- FIGURE 54 Three mRJ21 cables 199
- FIGURE 56 Five mRJ21 cables 199
- FIGURE 57 Six mRJ21 cables 200
- FIGURE 58 Seven mRJ21 cables 200
- RJ45 procedures 201
- 24 RJ45 cables in four groups 203
- 30 RJ45 cables in five groups 204
- 36 RJ45 cables in six groups 204
Související produkty a manuály pro Sítě Brocade Communications Systems S3-1002483-03
(44 stránky)
(94 stránky)LG DVD5353 manuales
Manuales del propietario y guías del usuario para Reproductores de dvd LG DVD5353.
Ofrecemos 3 manuales en pdf LG DVD5353 para descargar gratis por tipos de documentos: Manual de usuario
Komentáře k této Příručce